How to Install a Ghost Immobiliser
A ghost immobiliser is a hidden security device that protects your car from key cloning and hacking. It works by preventing the vehicle's engine from starting until it is started with PIN codes, which can be as long as 20 characters.
It is unnoticeable by thieves who don't think about this additional layer of security. Certain systems have an app that allows the owner to disable their immobiliser in the event of forgetting their PIN or use service/valet mode.
Connecting the vehicle's CAN Bus to the vehicle's
The Ghost 2 Immobiliser is a cutting-edge security system that can be incorporated into your vehicle's ECU, providing a discreet protection against thieves. It is extremely efficient and user-friendly and is a great component of your vehicle's security arsenal. However, like any anti-theft system, it is not impervious to failure and requires regular maintenance to ensure its operation. Luckily, this guide will help you get the most value from the Ghost 2 Immobiliser.
CAN (Controller Area Network) is a robust serial network that lets microcontrollers communicate with each other over short distances without the need for central control units. ghost autowatch immobiliser is designed for multiplexing electrical wiring inside vehicles to cut down on copper and comes with a variety of advantages, such as low cost and easy use.
The CAN protocol is utilized in a majority of modern cars to communicate with the engine management system, steering control module and air conditioning controls and many more. It also transmits data from sensors including speed sensors and inputs, to control various features of the car. The CAN bus is able to monitor the condition of these different components. It can prevent the vehicle from starting if it's in an unsafe condition.
While the CAN bus could be employed for a variety purposes, it's crucial to know how it functions and how it's secured. It is possible to add new features to vehicles using CAN bus, but it's important to secure it against attacks from hackers and other dangers. The best method to achieve this is to install firewalls and monitoring your CAN bus through software.
Ghost2's discreet control unit is concealed in the wiring harness or dashboard, eliminating the possibility of a criminal physically altering it. It's also impossible to reset the PIN code or emergency code without access to the vehicle.
If you have to give your car away for maintenance, valet parking, or any other reason, you can activate the Transport Mode. This feature turns off both the keyfob and ignition functions of the Ghost immobiliser. It will only be activated after the car has reached 31 mph over a period of 15 minutes.
How do I create a PIN code
The Ghost immobiliser protects your car from thieves. The innovative technology uses a PIN to disable the vehicle's engine and prevent it from starting without the right code, or a valid fob/mobile. The system's sleek design makes it unnoticeable, and also provides unbeatable protection against theft. The system is TASSA-certified and can save you significant amounts on your car insurance.
During installation, the Ghost system enters a learning mode to record the sequence of buttons pressed to generate your unique pin code. The installer will guide you through activating the system once the pin code has been created. Once activated, the Ghost system will shut down the starter motor of your vehicle unless a valid PIN is entered or the vehicle is switched to transport mode. This makes it extremely difficult for thieves or cloners to hack or clone your vehicle's starter system.
Installing a Ghost immobiliser is simple however it is essential to follow the precise instructions in the user's manual to ensure proper operation. Multimeters and hand tools are a good way to check electrical values. Insulation tape as well as heat shrink tubing and cable ties can be used to protect exposed wiring. Also, make certain to test the system regularly to identify any potential issues and mistakes.
After the installation is completed, it is important to perform a final check of the system prior to turning on your vehicle's ignition. Ghost immobilisers will re-arm themselves after 3 to 30 seconds dependent on the model of the vehicle. The system is also fitted with a Service/Valet Mode that lets you temporarily remove the system for servicing or valet parking.
Ideally, the immobiliser should be concealed in an inconspicuous location under the steering wheel or dashboard. It is recommended to use a small piece of duct tape or paint to mark the CAN H and L wires to ensure that you easily identify them when you are testing. The CAN H and the L wires must also be connected to an electrical source that can provide a constant 12V. It is also important to check the connections following testing, as a mistake in identifying these wires could cause the system to malfunction.
The system must be activated
A ghost immobiliser blocks the car from starting unless you press certain buttons in the vehicle, usually on the steering wheel or door panel, or the central console. The sequence is decided by the user and can be changed if necessary. Once activated, the system cannot be turned off. This is a fantastic option for anyone who wants to secure their vehicle against theft.
The device is not designed to be detectable by modern diagnostic and code-grabbing techniques. It also doesn't send out radio frequencies, which makes it even difficult for thieves to find the device.
If the device is detected, it will prevent the engine from running and sound an alarm with a loud sound to scare away the thief. The device can be used to monitor the location of the vehicle and assist police recover it in the event of theft.
If you are interested in a ghost-immobiliser call the experts at Car Specalist Customs to get an estimate and discuss your options. We are fully qualified to install a ghost immobiliser on your vehicle and will ensure it is concealed in a hard-to-reach area. We also offer other security measures like a wheel lock and kill switch to keep your car safe from thieves.
Disarming the System
It's important to understand how to disarm a Ghost immobiliser if it is fitted to your car. This will assist you in the event that you lock your keys inside the car or if your battery fails. The system utilizes a unique PIN code that only you know, and the immobiliser will not start your vehicle without entering this code. The most efficient method of entering the code is to press a set of buttons on your dashboard or steering wheel. This is much easier than using a key fob. It also keeps others from copying the remote.
Ghost2 is noninvasive, unlike some aftermarket immobilisers which require cutting wires for installation. It also works with the CAN bus system of your vehicle to function. Its main feature is its ability bypass the engine without affecting your vehicle's normal functions, making it difficult for thieves to use signal boosters to duplicate your car key. It doesn't emit radio frequencies, which means thieves are unable to detect it.
The Ghost system also features an option called Transport Mode that allows you to temporarily disable the security system for occasions like transportation or servicing. This feature is a great option if you want to lend your vehicle to a person who isn't sharing the PIN code or if you wish to secure your vehicle while driving it. To activate the Transport Mode you need to press the service button 5 times within 2 seconds. The Ghost system will confirm activation with 5 indication signals.
Save the emergency code in your vehicle in a safe place. If you ever get locked out of your vehicle, you can call the technician or the company that installed the system and they'll provide you with the code. If you are unable to reach them then you can try contacting an authorized dealer, but this will involve verification procedures and could incur additional costs.
This system is not only practical, but it can also help protect your vehicle from theft and reduce insurance costs. Many insurance companies offer lower monthly premiums or even financial incentives to install this anti-theft technology.